Barco BlendPRO-II Instruction Manual Page 200
- Page / 292
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
200 ScreenPRO-II Controller • User’s Guide
5. System Setup
Sync Setup
póåÅ=pÉíìé
ScreenPRO-II Controller system setup: Step 12
S Prerequisites — Ensure that you are familiar with the Settings Menu. In
Chapter 4, refer to the “
Settings Menu” section on page 104.
In this procedure, you will set up sync parameters for the monitors and projectors
connected to the system — for the destination selected on the
Output Menu.
Use the following steps to set up sync parameters:
1. From the Home Menu, press OUTPUT to display the Output Menu.
2. On the Destination Bus, select the destination that you want to configure.
3. Press {SETTINGS} to display the Settings Menu.
4. On the Output Monitor line, select the device(s) that are affected by the sync
settings —
All, Preview, SPII Program or BPII Program.
5. On the Sync Out line, set the desired sync value — +H+V, -H-V, +H-V, -H+V or
CSync.
6. On the SOG line, select a specific “sync on green” signal — Off, Standard or Tri-
Level
(for certain HD devices).
7. On the Gamma line, set the output gamma for the selected destination.
8. On the Raster Box Size line, set the size of the raster box that appears around
PIPs and Keys.
9. Press {BACK} to return to the Output Menu.
10. Repeat from step 2 to set sync parameters for additional destinations.
11. Press {HOME} to return to the Home Menu.
12. Press {SAVE} to save the new system configuration in memory.
12
Note
It is recommended that you leave the sync parameters at their
default (factory reset) values. However, should you need to
adjust individual settings for a particular monitor and projector
configuration, use the following procedure.
Important
It is recommended that you leave Gamma at the unity setting
(
1.0). Change the value only if you need to compensate for a
gamma problem in your projector or monitor.
Note
As required, you can change the Raster Box value during
operations without affecting sync settings.
- • Manual # 26-0505000-00 1
- • Revision A 1
- =√==rëÉêÛë=dìáÇÉ 2
- `çãé~åó=^ÇÇêÉëë 3
- ^sboqfppbjbkq> 5
- `Ü~åÖÉ=eáëíçêó 6
- Table of Contents 10
- NK==fåíêçÇìÅíáçå 15
- `Ü~éíÉê=píêìÅíìêÉ 16
- `çåîÉåíáçåë= 18
- ^=tçêÇ=^Äçìí=i~óÉêë 21
- Wilderness 22
- Background A ↔ B 29
- ^ééäáÅ~íáçå=nìÉëíáçåë 30
- OK==e~êÇï~êÉ=lêáÉåí~íáçå 31
- 2. Hardware Orientation 32
- Front Panel Sections 37
- Figure 2-3. Presets Section 39
- Figure 2-5. Joystick Section 42
- WIPE MIX 50
- TRANSITIONS 50
- PK==e~êÇï~êÉ=fåëí~ää~íáçå 53
- `çåíêçääÉê=fåëí~ää~íáçå 54
- 3. Hardware Installation 55
- `çååÉÅíáçå=`Ü~êíë= 56
- Destination Setup Menu) 63
- _ä~åâ=`çååÉÅíáçå=`Ü~êíë= 66
- ^ìñáäá~êó=aÉëíáå~íáçå=`Ü~êí 72
- `çåíÉåí=`êÉ~íáçå= 79
- _äÉåÇmolJff 80
- Blend Region 82
- Image Intensity 82
- QK==jÉåì=lêáÉåí~íáçå 85
- ScreenPRO II CONTROLLER 87
- • Input Menu Tree 88
- • Input Menu Description 88
- • Input Menu Functions 88
- • Input Sub Menus 88
- {APPLY FORMAT} to accept the 90
- Connector 91
- FORCE ACQUIRE 92
- FORCE ACQUIRE command 92
- File Name IFILE_001 93
- INPUT CONFIGURATION SRC_1 93
- File Number 1 93
- Delete Applies To: Dest 1 93
- ^ëéÉÅí=o~íáç=jÉåì 94
- NWN=páòáåÖ=jÉåì 95
- `çäçê=_~ä~åÅÉ=jÉåì 98
- 4. Menu Orientation 100
- • Output Menu Tree 100
- • Output Menu Description 100
- • Output Menu Functions 100
- • Output Sub Menus 100
- [V Lock] 103
- [Free-Run] 103
- Important 106
- 2 * 1024 - (200 * 1) = 1848 107
- • System Menu Tree 108
- • System Menu Description 108
- • System Sub Menus 108
- SYSTEM MENU 109
- Modify Layers On Program Off 109
- Tally Mode Off 109
- {NO} to cancel the procedure 111
- DIAGNOSTICS SETUP 113
- Reset Rotary Encoders Yes 113
- ^ìñ=aÉëíáå~íáçå=pÉíìé 120
- [SERVER] label 124
- `çãã=pÉíìé=jÉåìë 129
- RS-232 SETUP 130
- Baud Rate 9600 130
- [ 8 ]Data Bits 130
- [ NONE ]Parity 130
- [ 1 ]Stop Bits 130
- • Miscellaneous Menu Tree 133
- • Miscellaneous Sub Menus 133
- MISCELLANEOUS MENU 134
- `çåëçäÉ=mçêí=pÉíìé=jÉåì 135
- _~ÅâìéLoÉëíçêÉ=jÉåì 141
- HOME MENU 142
- Frame Grab 142
- Name Menu 142
- • PIP Adjustment Menu Tree 148
- • PIP Adjustment Sub Menus 148
- _çêÇÉê=jÉåì 151
- • Key Menu Tree 155
- • Key Menu Description 155
- • Key Menu Functions 155
- • Key Sub Menus 155
- `çäçê=hÉó=cìåÅíáçåë 157
- `ìí=H=cáää=hÉó=cìåÅíáçåë 158
- Green 204 159
- Blue 260 159
- TRACK RGB 159
- `äçåÉ=pÉíìé=jÉåì 162
- `êçé=jÉåì 164
- 50 is 50 pixels to the right 168
- _~ÅâÖêçìåÇ=fåéìí=pÉíìé=jÉåì 170
- Crop: V Offset 171
- DestinatDestination [ 1 ] 172
- _d=j~ííÉ=jÉåì 174
- Destinat 176
- RK==pó ëíÉã=pÉíìé 183
- 5. System Setup 185
- {NEXT IP 193
- {DISCOVER LTRX} 193
- ^ru=aÉëíáå~íáçå=pÉíìé 195
- _~ÅâÖêçìåÇ=pÉíìé 205
- • Standard Input Setup 206
- APPLY FORMAT} to accept 206
- `çäçê=_~ä~åÅÉ=^ÇàìëíãÉåíë 210
- {FORCE ACQUIRE} 211
- _~Åâìé=íç=cä~ëÜ=jÉãçêó=`~êÇ 213
- SK==léÉê~íáçåë 215
- 6. Operations 218
- • Left Justified Markers 218
- • Center Justified Markers 218
- ^=tçêÇ=^Äçìí=ilp 221
- ^Åíáî~íáåÖ=aÉëíáå~íáçåë 222
- `äÉ~êáåÖ=aÉëíáå~íáçåë 223
- _~ÅâÖêçìåÇ=qê~åëáíáçåë 227
- `äÉ~êáåÖ=i~óÉêë=Ñêçã=mêçÖê~ã 234
- `Ü~åÖáåÖ=íÜÉ=i~óÉê=jçÇÉ 235
- • Pend on Preview 239
- • Pend on Program 239
- ^=tçêÇ=^Äçìí=oÉëçìêÅÉë 243
- Previous 245
- ^K==péÉÅáÑáÅ~íáçåë 255
- _K==` çåí~Å í=fåÑçêã~íáçå 267
- `çåí~Åí=fåÑçêã~íáçå 268
- `K==réÖê~ÇáåÖ=pçÑíï~êÉ 269
Related products and manuals for Processors Barco BlendPRO-II
Processors Barco LED-PRO Instruction Manual
(186 pages)
(186 pages)
Processors Barco Encore VPx User Manual
(12 pages)
(12 pages)
Processors Barco LED-PRO User Manual
(60 pages)
(60 pages)
Processors Barco Encore VPx Specifications
(30 pages)
(30 pages)
Processors Barco BlendPRO-II User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 1.896 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals