Barco BlendPRO-II Instruction Manual Page 213
- Page / 292
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ScreenPRO-II Controller • User’s Guide 213
5. System Setup
Saving the Setup
p~îáåÖ=íÜÉ=pÉíìé
ScreenPRO-II Controller system setup: Step 19
When all system setup procedures have been complete, press {HOME} to display the
Home Menu, then press {SAVE}. This action saves the state of the Controller in non-
volatile memory.
Once pressed, the Touch Screen menu reads “
Saving System Configuration.” If you
cycle power, the Controller will return to its state at the time of the “save.”
_~Åâìé=íç=cä~ëÜ=jÉãçêó=`~êÇ
ScreenPRO-II Controller system setup: Step 20
S Prerequisites — Ensure that you are familiar with the Backup/Restore
Menu
. In Chapter 4, refer to the “Backup/Restore Menu” section on
page 141.
In this procedure, you will back up your system configuration to a
Flash Memory Card.
Use the following steps to back up your system:
1. Ensure that you have a (customer supplied) Flash Memory Card available.
2. Insert the Flash Memory Card into the Controller’s rear panel Memory Card slot.
3. From the Home Menu, press MISC to display the Miscellaneous Menu.
4. Press {BACKUP RESTORE} to display the Backup/Restore Menu.
5. On the Device line, select Ctrlr+SP to perform a complete “backup.”
6. On the Controller Options line, select All.
7. Press {CHECK CARD} to check for the presence of a Flash Memory Card.
8. Press {BACKUP} to perform a backup operation to the Flash Memory Card using
the selected device(s) and options.
19
20
Note
You can only store one system configuration on a Flash
Memory Card.
- • Manual # 26-0505000-00 1
- • Revision A 1
- =√==rëÉêÛë=dìáÇÉ 2
- `çãé~åó=^ÇÇêÉëë 3
- ^sboqfppbjbkq> 5
- `Ü~åÖÉ=eáëíçêó 6
- Table of Contents 10
- NK==fåíêçÇìÅíáçå 15
- `Ü~éíÉê=píêìÅíìêÉ 16
- `çåîÉåíáçåë= 18
- ^=tçêÇ=^Äçìí=i~óÉêë 21
- Wilderness 22
- Background A ↔ B 29
- ^ééäáÅ~íáçå=nìÉëíáçåë 30
- OK==e~êÇï~êÉ=lêáÉåí~íáçå 31
- 2. Hardware Orientation 32
- Front Panel Sections 37
- Figure 2-3. Presets Section 39
- Figure 2-5. Joystick Section 42
- WIPE MIX 50
- TRANSITIONS 50
- PK==e~êÇï~êÉ=fåëí~ää~íáçå 53
- `çåíêçääÉê=fåëí~ää~íáçå 54
- 3. Hardware Installation 55
- `çååÉÅíáçå=`Ü~êíë= 56
- Destination Setup Menu) 63
- _ä~åâ=`çååÉÅíáçå=`Ü~êíë= 66
- ^ìñáäá~êó=aÉëíáå~íáçå=`Ü~êí 72
- `çåíÉåí=`êÉ~íáçå= 79
- _äÉåÇmolJff 80
- Blend Region 82
- Image Intensity 82
- QK==jÉåì=lêáÉåí~íáçå 85
- ScreenPRO II CONTROLLER 87
- • Input Menu Tree 88
- • Input Menu Description 88
- • Input Menu Functions 88
- • Input Sub Menus 88
- {APPLY FORMAT} to accept the 90
- Connector 91
- FORCE ACQUIRE 92
- FORCE ACQUIRE command 92
- File Name IFILE_001 93
- INPUT CONFIGURATION SRC_1 93
- File Number 1 93
- Delete Applies To: Dest 1 93
- ^ëéÉÅí=o~íáç=jÉåì 94
- NWN=páòáåÖ=jÉåì 95
- `çäçê=_~ä~åÅÉ=jÉåì 98
- 4. Menu Orientation 100
- • Output Menu Tree 100
- • Output Menu Description 100
- • Output Menu Functions 100
- • Output Sub Menus 100
- [V Lock] 103
- [Free-Run] 103
- Important 106
- 2 * 1024 - (200 * 1) = 1848 107
- • System Menu Tree 108
- • System Menu Description 108
- • System Sub Menus 108
- SYSTEM MENU 109
- Modify Layers On Program Off 109
- Tally Mode Off 109
- {NO} to cancel the procedure 111
- DIAGNOSTICS SETUP 113
- Reset Rotary Encoders Yes 113
- ^ìñ=aÉëíáå~íáçå=pÉíìé 120
- [SERVER] label 124
- `çãã=pÉíìé=jÉåìë 129
- RS-232 SETUP 130
- Baud Rate 9600 130
- [ 8 ]Data Bits 130
- [ NONE ]Parity 130
- [ 1 ]Stop Bits 130
- • Miscellaneous Menu Tree 133
- • Miscellaneous Sub Menus 133
- MISCELLANEOUS MENU 134
- `çåëçäÉ=mçêí=pÉíìé=jÉåì 135
- _~ÅâìéLoÉëíçêÉ=jÉåì 141
- HOME MENU 142
- Frame Grab 142
- Name Menu 142
- • PIP Adjustment Menu Tree 148
- • PIP Adjustment Sub Menus 148
- _çêÇÉê=jÉåì 151
- • Key Menu Tree 155
- • Key Menu Description 155
- • Key Menu Functions 155
- • Key Sub Menus 155
- `çäçê=hÉó=cìåÅíáçåë 157
- `ìí=H=cáää=hÉó=cìåÅíáçåë 158
- Green 204 159
- Blue 260 159
- TRACK RGB 159
- `äçåÉ=pÉíìé=jÉåì 162
- `êçé=jÉåì 164
- 50 is 50 pixels to the right 168
- _~ÅâÖêçìåÇ=fåéìí=pÉíìé=jÉåì 170
- Crop: V Offset 171
- DestinatDestination [ 1 ] 172
- _d=j~ííÉ=jÉåì 174
- Destinat 176
- RK==pó ëíÉã=pÉíìé 183
- 5. System Setup 185
- {NEXT IP 193
- {DISCOVER LTRX} 193
- ^ru=aÉëíáå~íáçå=pÉíìé 195
- _~ÅâÖêçìåÇ=pÉíìé 205
- • Standard Input Setup 206
- APPLY FORMAT} to accept 206
- `çäçê=_~ä~åÅÉ=^ÇàìëíãÉåíë 210
- {FORCE ACQUIRE} 211
- _~Åâìé=íç=cä~ëÜ=jÉãçêó=`~êÇ 213
- SK==léÉê~íáçåë 215
- 6. Operations 218
- • Left Justified Markers 218
- • Center Justified Markers 218
- ^=tçêÇ=^Äçìí=ilp 221
- ^Åíáî~íáåÖ=aÉëíáå~íáçåë 222
- `äÉ~êáåÖ=aÉëíáå~íáçåë 223
- _~ÅâÖêçìåÇ=qê~åëáíáçåë 227
- `äÉ~êáåÖ=i~óÉêë=Ñêçã=mêçÖê~ã 234
- `Ü~åÖáåÖ=íÜÉ=i~óÉê=jçÇÉ 235
- • Pend on Preview 239
- • Pend on Program 239
- ^=tçêÇ=^Äçìí=oÉëçìêÅÉë 243
- Previous 245
- ^K==péÉÅáÑáÅ~íáçåë 255
- _K==` çåí~Å í=fåÑçêã~íáçå 267
- `çåí~Åí=fåÑçêã~íáçå 268
- `K==réÖê~ÇáåÖ=pçÑíï~êÉ 269
Related products and manuals for Processors Barco BlendPRO-II
Processors Barco LED-PRO Instruction Manual
(186 pages)
(186 pages)
Processors Barco Encore VPx User Manual
(12 pages)
(12 pages)
Processors Barco LED-PRO User Manual
(60 pages)
(60 pages)
Processors Barco Encore VPx Specifications
(30 pages)
(30 pages)
Processors Barco BlendPRO-II User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.105 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals