Barco ScreenPRO-II Instruction Manual Page 135
- Page / 206
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ScreenPRO-II • User’s Guide 123
6. Operations
Working with Layers
With both Mix Source and Swap modes, one additional “transition” function can be used
without restriction.
Figure 6-7. System Menu: Toggle Mode Enabled
• With Toggle mode enabled, sources toggle back and forth with each transition.
When a PIP or Key source is selected in Preview and a transition is performed,
the Program source “flip-flops” to Preview. Subsequent transitions simply
alternate between sources. Any new source can be selected in Preview, and as
long as
Toggle is on, the last two selected sources will alternate.
• With Toggle off, the source selected in Preview stays in Preview, once the
transition is complete. In this mode, you are required to change Preview sources
manually.
Please note the following important points regarding
Mix Mode:
• In Mix Mode, there is always a layer available In Preview for a new source to be
selected and taken to Program.
• Four transition combinations are possible:
~ Mix Source with Toggle On
~ Mix Source with Toggle Off
~ Swap with Toggle On
~ Swap with Toggle Off
tçêâáåÖ=ïáíÜ=mfmë=áå=péäáí=jçÇÉ
In Split Mode, the mixer’s two layers operate independently.
Use the following steps to work with PIPs in Split Mode.
1. In the Mixer Functions Section, ensure that the Split Layer button is On.
2. Press the desired layer button (A or B). Please note:
~ The layer button blinks to indicate that it is active for modification.
~ In the Source Selection Bus, the source currently assigned to the layer
blinks.
~ On the Preview monitor, the raster box for the selected layer blinks (even
if it is hidden under another layer).
3. In the Mixer Functions Section, ensure that the PIP button is lit and the PIP
Adjustment Menu
is visible. If the menu is not visible, press PIP.
Toggle On
Note
Even though this mode allows you to display two PIPs (or
Keys) on air, it is more restrictive. Once both layers are on
Program, you must transition them off Program, make
changes — and then transition them back on.
LAYER
A
Note
Even if the layer is on Program, the PIP Adjustment Menu
appears, but parameters can not be adjusted.
- • Manual # 26-0407000-00 1
- • Revision B 1
- =√=rëÉêÛë=dìáÇÉ 2
- `çãé~åó=^ÇÇêÉëë 3
- ^sboqfppbjbkq> 5
- `Ü~åÖÉ=eáëíçêó 6
- Table of Contents 10
- NK==fåíêçÇìÅíáçå 13
- `çåîÉåíáçåë= 14
- Wilderness 18
- Background 19
- OK==e~êÇï~êÉ=lêáÉåí~íáçå 23
- 2. Hardware Orientation 24
- ^å~äçÖ=fåéìí=cäÉñáÄáäáíó 26
- Front Panel Sections 30
- WIPE CUT MIX 35
- Transitions 35
- `~ÄäÉ=~åÇ=^Ç~éíÉê=fåÑçêã~íáçå 41
- 3. Hardware Installation 43
- BORDER} to … 47
- ScreenPRO II 48
- INPUT MENU 49
- Input Type 51
- INPUT ACQUISITION SRC_3 53
- Source acquired 53
- File Name [ IFILE_003 ] 54
- INPUT CONFIGURATION SRC_3 54
- File Number [ 3 ] 54
- NWN=páòáåÖ=jÉåì 55
- `çäçê=_~ä~åÅÉ=jÉåì 57
- ^ëéÉÅí=o~íáç=jÉåì 58
- OUTPUT MENU 59
- TEST PATTERN 63
- Output Monitor All 63
- Raster Box On 63
- SYSTEM MENU 64
- NVRAM Battery [ OK ] 67
- DIAGNOSTICS SETUP 67
- Reset Rotary Encoders Yes 67
- Encoder Menu 68
- Figure 4-21. Reset Menu 70
- SOFTWARE VERSION 71
- ScreenPRO II 1.00 71
- SERIAL 1 PORT SETUP 72
- Baud Rate 115200 72
- 8Data Bits 72
- NONEParity 72
- 1Stop Bits 72
- System Menu 74
- EFFECTS MENU 75
- Transition Rate 1.0 75
- Transition Wipe Wipe Down 75
- Transition Edge 16 75
- Key Frame Effect [ LINEAR ] 75
- Status Menu 76
- DISPLAY SETTINGS 77
- Brightness 85 77
- Contrast 97 77
- Backlight Menu 78
- ADJUSTMENT 79
- _çêÇÉê=jÉåì 82
- `êçé=jÉåì 83
- Key Menu 87
- Green 204 90
- Blue 260 90
- TRACK RGB 90
- -10 is 10 pixels below its 95
- _~ÅâÖêçìåÇ=fåéìí=pÉíìé=jÉåì 96
- _~ÅâÖêçìåÇ=j~ííÉ=jÉåì 99
- Save Now? 101
- DSK ADJUSTMENT 102
- Important 104
- {SELECT 105
- 4. Menu Orientation 110
- RK==pó ëíÉã=pÉíìé 111
- 5. System Setup 112
- `çãéêÉÜÉåëáîÉ=fåéìí=pÉíìé 116
- SK==léÉê~íáçåë 127
- ProgramPreview 129
- ^=tçêÇ=^Äçìí=ilp 131
- _~ÅâÖêçìåÇ=qê~åëáíáçåë 133
- Toggle On 135
- 6. Operations 137
- `äÉ~êáåÖ=i~óÉêë=Ñêçã=mêçÖê~ã 140
- `Ü~åÖáåÖ=íÜÉ=i~óÉê=jçÇÉ 141
- • Pend on Preview Method 145
- • Pend on Program Method 145
- `~éíìêáåÖ=píáää=cê~ãÉë 149
- ^K==péÉÅáÑáÅ~íáçåë 153
- ^å~äçÖ=NRJéáå=a=`çååÉÅíçê 158
- _K==` çåí~Åí=fåÑçêã~íáçå 165
- `çåí~Åí=fåÑçêã~íáçå 166
- `K==réÖê~ÇáåÖ=pçÑíï~êÉ 167
- {ADD NEW} 191
- INPUT SOURCE PATCH 194
- Source Number 1 194
- MATRIXPRO1Connection Type 194
- 1Router Input 194
- Feature ScreenPRO-II 196
- Encore Video 196
- Processor 196
Related products and manuals for TVs & monitors Barco ScreenPRO-II
(136 pages)
(120 pages)
TVs & monitors Barco MDRC Series User Manual
(66 pages)
(66 pages)
TVs & monitors Barco MFGD 2320 User Manual
(36 pages)
(36 pages)
TVs & monitors Barco MFGD 3220 D User Manual
(19 pages)
(19 pages)
TVs & monitors Barco MFGD 2320 User Manual
(100 pages)
(100 pages)
TVs & monitors Barco MFCD 1218 User Manual
(19 pages)
(19 pages)
TVs & monitors Barco MIVD 1218 User Manual
(31 pages)
(31 pages)
TVs & monitors Barco Nio 5MP User Manual
(99 pages)
(99 pages)
TVs & monitors Barco mDR+50-DL User Manual
(81 pages)
(81 pages)
© 2020, manymanuals.com. All rights reserved. | 0.099 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals