Barco R9040341 Owner's Manual

Trace+Owner’s ManualR9040341R5976781/0014/09/2004

1. Safety InstructionsImage 1-1The Air Outlet Grill on the side of the Projector can reach high temperaturesWARNING: Do not touch this Air Outlet Gril

6. Random Access6.5.7.9.7 Basic Soft Edge Shape Set upThe following procedures will adjust the Shape of a basic Electronic Soft Edge set up with 2 pro

6. Random AccessImage 6-47Basic Shape set up for Projector 1Setting up the Shape for Projector 21. Use the combination of ENTER and the cursor key ← o

6. Random Access6.5.7.9.8 Soft Edge Width Start upWhen Soft Edge is not installed on the projector or when the Soft Edge Active mode is set to [OFF] t

6. Random AccessImage 6-50Soft Edge Width selections6.5.7.9.10 Basic Soft Edge Width Set upSetting up the Width for Projector 1 ?1. Press ENTER until

6. Random AccessImage 6-52Basic Width set up for Projector 1Setting up the Width for Projector 2 ?1. Press ENTER until Left is selected. (image 6-53)2

6. Random Access6.5.7.10 ResetOverview•Startup• Coarse Reset• Linearity Reset• Reset Fine• Reset Blanking/Soft Edge• Reset AllWhat can be done with Re

6. Random Access6.5.7.10.3 Linearity ResetHow to reset the Linearity adjustments ?1. Push the cursor key ↑ or ↓ to highlight Line arity within the Geo

6. Random Access4. Press ENTER to select the desired Blanking/Soft Edge Reset value.A warning will be displayed . (menu 6-127)5. Press ENTER to reset

6. Random Access6.5.8 RenameStart UpTo change the name of a selected file:1. Push the cursor key ↑ or ↓ to highlight Rename. (menu 6-130)2. Press ENTE

6. Random Access6.5.9 CopyStart UpTo copy the name of a selected file :1. Push the cursor key ↑ or ↓ to highlight C opy . (menu 6-133)2. Press ENTER.T

2. Packaging and Dimensions2. PACKAGING AND DIMENSIONSThis chapter handles about the way the Trace+ is packed and gives an overview of the dimensions.

6. Random Access4. Press ENTER to select.If [all] is selected, your password has to be entered before all files will be deleted.A confirmation menu &q

6. Random AccessImageFrame LeftStereo Sync LeftRightDelay TimeStereo Sync LeftRightFrame LeftFrame RightWithout Stereo Phase AdjustmentWith Stereo Pha

6. Random AccessWe advise to set Invert Stereo ON, one frame delay is inherent to DLP technology.ImageFrame LeftStereo Sync LeftRightFrame LeftFrame R

6. Random AccessHow to Select Master Channel?1. Push the cursor key ↑ or ↓ to highlight Master Channel. (menu 6-143)2. Press ENTER to toggle between [

6. Random AccessLeft ShutterOpenOpeningOpeningClosingClosingClosedRight ShutterOpenClosedDLP MirrorsActiveBlanking TimeOpening + Closing = Blanking Ti

6. Random AccessLeft ShutterOpenOpeningOpeningClosingClosingClosedRight ShutterOpenClosedDLP MirrorsActiveBlanking TimeOpening Too Late and/or Closing

6. Random Access6.6.7 Forced AsynchronousWhat is Synchronous Mode?When the IG provides a signal within the range from 96Hz to 108Hz, the projector wil

7. Installation Mode7. INSTALLATION MODEOverview• Installation Mode Overview• Starting Up Installation• Input Slots•NoSignal• Lens Adjustment• Changin

7. Installation Mode7.2 Starting Up InstallationHow to Start Up Installation?1. Press ADJUST or ENTER key to start up the Adjustment Mode.The Adjustme

7. Installation ModeHow to change the Slot Selection?1. Push the cursor key ↑ or ↓ to highlight Slot Selection.2. Press ENTER to toggle between [AUTOM

2. Packaging and Dimensions2.2 Box ContentCAUTION: Do not unpack the Trace+ to check this content list, First read this manual and follow the Installa

7. Installation ModeHow to Change the Background Color?1. Push the cursor key ↑ or ↓ to highlight Color. (menu 7-7)2. Press ENTER to toggle between th

7. Installation Mode7.5 Lens AdjustmentOverview• Starting Up Lens Adjustment• Lens Zoom/Focus Adjustment• Lens Shift Adjustment7.5.1 Starting Up Lens

7. Installation ModeLENS ADJUSTMENT ZOOM/FOCUSZOOM with or ,FOCUS with or <ENTER> to shift<EXIT> to returnImage 7-1Zoom/Focu

7. Installation ModeHow to change the Menu Position?1. Push the cursor key ↑ or ↓ to highlight Menu Position . (menu 7-14)2. Press ENTER to toggle bet

7. Installation ModeDefining the Communication Protocol1. Push the cursor key ↑ or ↓ to highlight Infrared. (menu 7-17)2. Press ENTER to toggle betwee

7. Installation Mode4. Press ENTER to confirm.The Projector will display the image according to the selected configuration.5. Press EXIT to return to

7. Installation ModeAvailable patterns- Outline-Hatch- Color bars- Multiburst- Checker board-Purity- Page Char- Alpha numeric char- Character SetsHow

8. Service Mode8. SERVICE MODE8.1 Service Mode OverviewService Mode Overview• Identification• Change Password• Change Proj. Address- Projector Address

8. Service Mode8.3 Starting Up ServiceHow to Start Up Service?1. Press ADJUST or ENTER key to start up the Adjustment Mode.The Adjustment Mode menu wi

8. Service ModeHow to display the Identification Screen?1. Push the cursor key ↑ or ↓ to highlight Identification. (menu 8-3)2. Press ENTER to select.

2. Packaging and Dimensions1390 mm(54.7 inch)1110 mm(43.7 inch)2050 mm(80 7 inch)905 mm(35.6 inch)Image 2-2Front View DimensionsR5976781 TRACE+ 14/09/

8. Service Mode8.6.1 Starting Up Change Projector AddressHow to Start Up Change Projector Address?1. Push the cursor key ↑ or ↓ to highlight Change Pr

8. Service Mode8.6.3 Changing the Common AddressHow to Change the Common Address?1. Push the cursor key ↑ or ↓ to highlight the active Common Address

8. Service ModeHow to Change Baudrate PC?1. Push the cursor key ↑ or ↓ to highlight Cha nge Baudrate PC. (menu 8-11)2. Press ENTER to select.The C han

8. Service ModeHow to Start Up the Lamp Menu?1. Push the cursor key ↑ or ↓ to highlight Lamp. (menu 8-13)2. Press ENTER to select.The Lamp Menu will b

8. Service Mode8.8.3 Linked CLOLinked CLO will be grayed out when Constant Light Output is set to Off.How to change the Linked CLO setting?1. Push the

8. Service Mode8.9 Barco Logo8.9.1 Starting Up Barco LogoWhat can be done?The Barco Logo can be added to the projected image, in overlay or on a backg

8. Service Mode8.9.3 Barco Logo BackgroundHow the Change the Barco Logo Background Setting?1. Push the cursor key ↑ or ↓ to highlight Background. (men

8. Service Mode8.9.5 Hot KeyHow to Change the Hot Key Setting?1. Push the cursor key ↑ or ↓ to highlight Hot Key. (menu 8-25)2. Press ENTER to toggle

8. Service ModeHow to Start Up Preset Input Balance 2?1. Push the cursor key ↑ or ↓ to highlight Preset Input Balance 2. (menu 8-28)2. Press ENTER to

8. Service Mode5. Press EXIT to return to the Convergence menu.6. Press EXIT to return to Service menu.SERVICEBARCO LOGOPRESET INPUT BALANCE 1PRESET I

2. Packaging and Dimensions759 mm(29.9 inch)67 mm(3 inch)Image 2-3Right View Dimensions1390 mm(54.7 inch)1635 mm(64.4 inch)760 mm(29 9 inch)178 mm(7.0

8. Service ModeFollowing IC’s are shown in the I2C info screen.• Motor Driver• Light Sensor• Lamp Driver• Power Supply• Formatter• LCD Driver• Lamp Mo

8. Service ModeHow to display the SMPS Diagnosis screen?1. Push the cursor key ↑ or ↓ to highlight SMPS. (menu 8-38)2. Press ENTER to select.The SMPS

8. Service ModeImage 8-2Due to the tolerance on optical components the x, y values of this color gamut of each projector will differ.Image 8-3When wor

8. Service ModeHow to Start Up DynaColor™?1. Push the cursor key ↑ or ↓ to highlight Diagnosis . (menu 8-40)2. Press ENTER to select.The DynaC olor me

8. Service Mode140 R5976781 TRACE+ 14/09/2004

9. Standard Source Files9. STANDARD SOURCE FILES9.1 Table overviewTable overviewThe following standard source files are pre-programmed in the projecto

9. Standard Source Files142 R5976781 TRACE+ 14/09/2004

IndexINDEXNumerics/Symbols% of image 91%% of image 91800 Peripheral 119800–Peripheral 119Starting Up 119AAddress 36Common 36Projector 36RCU 36Adjustme

IndexSelection 85Quadrant 83–84Adjustment 84Selection 83Start up 79Vertical Linearity 79–80Adjustment 80Selection 79Forced 112Asynchronous 112Forced A

IndexNNo Signal 115Starting Up 115OOperate 21Operating the projector 30Options 50File 50OSD 121Color 121OSD Color 33Quick 33Change 33Overview 20Connec

2. Packaging and DimensionsImage 2-5Bottom View DimensionsR5976781 TRACE+ 14/09/2004 11

IndexWWARP1 43Edit 43WARP2 44Edit 44Windowing 56Blanking 56Start Up 56146R5976781 TRACE+ 14/09/2004

Revision SheetTo:Barco nv Simulation ProductsNoordlaan 5, B-8520 KuurnePhone: +32 56.36.82.11, Fax: +32 56.36.84.86E-mail: [email protected], Web: www.ba

2. Packaging and Dimensions12 R5976781 TRACE+ 14/09/2004

3. Installation Guidelines3. INSTALLATION GUIDELINES3.1 IntroductionInstallation ManualThis chapter will describe some general installation guidelines

3. Installation Guidelines3.3 Restricted Access LocationInstallation in a Restricted Access LocationThe Trace+ can only be installed in a Restricted A

3. Installation GuidelinesImage 3-2Projector positionCAUTION: Never use the projector when turned with the inputs downwards.3.5 Re-adjusting the lamp

Barco nv Simulation Products600 Bellbrook Ave, Xenia OH 45385Phone: +1 (937) 372 7579Fax: +1 (937) 372 8645E-mail: [email protected] us at the web: w

3. Installation GuidelinesImage 3-3Push on the top corners of the Front Panel untill a click is heardImage 3-4Push on the top corners of the front pan

3. Installation GuidelinesImage 3-7Flip the cover to the left side and take offHow to re-adjusting the lamp position?1. Start up the adjustment mode a

3. Installation GuidelinesAImage 3-8CAUTION: Never turn the other screws ! These are factory aligned.3.6 Battery Installation in the RCUHow are the ba

4. Trace+ Connections4. TRACE+ CONNECTIONSThe following procedures will describe the connections when installing a single Trace+.Overview• Connections

4. Trace+ Connections4.2 Connections OverviewConnections Overview23874615Image 4-2Connections Overview1Power Cord Connection25–BNC Cable Input3 DVI In

4. Trace+ ConnectionsImage 4-3Power Cord Connection4.4 Operating the Trace+Overview• Switching On• Switching to Standby• Switching Off4.4.1 Switching

4. Trace+ ConnectionsHow to Start Image Projection?1. Press the Standby key on the RCU. (image 4-5)Tip: Point the RCU towards the Trace+ Screen .Note:

4. Trace+ ConnectionsImage GeneratorImage 4-6RGB InputWhich signals can be connected to the Source Connection?Connector name/Input signalRGB H VRGBHVR

4. Trace+ ConnectionsHow to select the Source Connection?1. Key in 1 on the RCU.How to change the Source Connection (Input 1) setting?1. Press ADJUST

4. Trace+ ConnectionsPossible indications on input slot menu• Input 1:- RGS-SS [CV or HS&VS] = RGB analog signals, separate sync is composite sync

Copyright ©All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted orst

4. Trace+ ConnectionsRCVDS 05 switcher(R9827880)Image 4-8Communication PortWhat is possible when connecting Barco’s RCVDS05?• Up to 20 inputs with Bar

4. Trace+ ConnectionsImage GeneratorImage 4-9Stereo Sync Connection4.8 Multi-Channel ConnectionsMulti-Channel ConnectionsFor more information on ’how

4. Trace+ Connections28 R5976781 TRACE+ 14/09/2004

5. Getting Started5. GETTING STARTED5.1 RCU & Local keypadThe local keypad is located on the input side of the projector and can only be accessed

5. Getting Started3 Address key(recessed key), to enter the address of the projector (between 0 and 9). Press the recessedaddress key with a pencil, f

5. Getting StartedF1F2F3F4F5ADJEXITENTERPAUSEPHASETEXTSHARPNTINTCOLORBRIGHTNCONTRTREBLE BALANCEBASSVOL9078563412Image 5-2Standby key on the RCULamp ru

5. Getting Started5.3.3 Switching OffHow to Switch Off the Projector?1. Frist switch the Projector to Standby.2. Let cool down the projector until the

5. Getting StartedHow to Focus the Lens?1. Loosen the 2 bolts connecting the Top Rear Cover to the Barco Trace. (image 5-5)2. Remove the Top Rear Cove

5. Getting Started5.4 Using the RCUPointing to the Screen1. Point the front of the RCU to screen. (image 5-7)RCUBarco TRACEImage 5-7Point the front of

5. Getting Started• Whenever the IR Sensor on the projector receives an IR signal the Red IR–Received Led will light up.Image 5-8IR-Received Led• In c

5. Getting Started5.5.1 Common AddressWhat is Common Address 0?Every projector has a Common Address default set to ’0’, when the RCU is set to address

5. Getting StartedF1F2F3F4F5ADJEXITENTERPAUSEPHASETEXTSHARPNTINTCOLORBRIGHTNCONTRTREBLE BALANCEBASSVOL9078563412Image 5-10Address Key5.5.4 Input Selec

5. Getting StartedBrightnessA correct ’brightness’ setting is important for good image reproduction.Use the + button for a higher brightness.Use the -

6. Random Access6. RANDOM ACCESSOverview• Random Access Overview• Starting Up Random Access• File Service• Picture Tuning• Geometry• Stereo Options6.1

6. Random Access• Geometry- Load-EditoCoarseoLinearityoFineoShiftoTransport DelayoMode [Automatic/Manual]oTransport Delay SettingoBlanking/Soft Edge (

6. Random AccessImage 6-1Adjust or Enter key6.3 File ServiceOverview• File annotation• Possible file manipulations• StartingUpFileService• Load File•E

6. Random Access6.3.2 Possible file manipulationsConnecting a new source.Before using a new source, a correct file has to be installed. The projector’

6. Random AccessHow to change the Filter List Setting?1. Push the cursor key ↑ or ↓ to to highlight filter list.2. Press ENTER to toggle the annotatio

6. Random AccessHow to Start Up Edit WARP1 File?1. Push the cursor key ↑ or ↓ to highlight Edit WARP1. (menu 6-9)2. Press ENTER to select.The Edit fil

6. Random AccessHow to change a setting with the numeric keys?1. Push the cursor key ↑ or ↓ to highlight an item.The color of the selected item will c

Table of contentsTABLE OF CONTENTS1. Safety Instructions...

6. Random AccessVertical Start number of lines between the start of the input signal and start of the image onthe screen.Read AMDS AMDS = automatic mo

6. Random AccessField selectDefault [both]The field select is only used for interlaced images. One frame of an interlaced image contains twofields, an

6. Random Access6.3.10 Rename FileHow to Start Up File Rename?1. Push the cursor key ↑ or ↓ to highlight Re name. (menu 6-17)2. Press ENTER to select.

6. Random Access6.3.11 Copy FileHow to Start Up Copy File?1. Push the cursor key ↑ or ↓ to highlight Copy. (menu 6-20)2. Press ENTER to select.The Cop

6. Random Access4. Press ENTER to select.If [ALL] is selected, your password has to be entered before all files will be deleted.A confirmation menu &q

6. Random AccessFile Load1. Push the cursor key ↑ or ↓ to highlight File Load. (menu 6-28)2. Press ENTER to toggle between [AUTOMATIC] or [MANUAL].Thi

6. Random Access6.4.1 Starting Up Picture TuningHow to Start Up Picture Tuning?1. Push the cursor key ↑ or ↓ to highlight Picture Tuning.2. Press ENTE

6. Random AccessSteps to be takenTo adjust the input balance, the following steps have to be executed in the following order:1. The procedure is best

6. Random AccessImage 6-3Full black image on the sourceImage 6-4Perfect Black BalanceHow to adjust the White Balance?1. Generate a full white image on

6. Random AccessImage 6-5Full white image on the sourceImage 6-6Perfect White BalanceHow to return to the Default Factory Preset?1. Push the cursor ke

Table of contents6.4.2 Gamma ...5

6. Random AccessHow to Start Up Input Balance 2?1. Push the cursor key ↑ or ↓ to highlight Input Balance 2. (menu 6-37)2. Press ENTER to select.The In

6. Random AccessHow to Start Up Windowing (Blanking)?1. Push the cursor key ↑ or ↓ to highlight Blanking. (menu 6-41)2. Press ENTER to select.The Blan

6. Random AccessImage 6-8Blanking (Windowing) adjustmentHow to reset the Blanking adjustment(s)?1. Push the cursor key ↑ or ↓ to highlight Reset. (men

6. Random AccessHow to Start Up the Shift adjustment?1. Push the cursor key ↑ or ↓ to highlight Shift. (menu 6-45)2. Press ENTER to select.A barscale

6. Random Access6.4.5.4 Size (Windowing)What can be done with Size (Windowing)?With the Size function it is possible to adjust the size of the image w

6. Random Access6.4.5.5 Geo Soft EdgeWhatcanbedonewithGeoSoftEdge?When setting up a soft edge (see Electronic Soft Edge), these setting are applied on

6. Random Access6.5.2 Starting Up GeometryHow to Start Up Geometry?1. Push the cursor key ↑ or ↓ to highlight Geometry. (menu 6-48)2. Press ENTER to s

6. Random Access6.5.6 LoadHow to start up ?To start up the Loa d File menu, handle as follow :1. Push the cursor key ↑ or ↓ to highlight Load. (menu 6

6. Random Access6.5.7 EditOverview• Introduction•Startup• Coarse• Linearity adjustment•Fine•Shift• Transport Delay•Blanking• Electronic Soft Edge (Opt

6. Random Access6.5.7.1 IntroductionHowdoesitwork?• The projected image on the screen is divided in 81 zones. Each zone represents a grid point that c

Table of contents6.6.4 Master Channel . ...

6. Random Access6.5.7.2 Start upHow to Start up the Edit mode ?1. Push the cursor key ↑ or ↓ to highlight Edit in the G eometry Files menu. (menu 6-53

6. Random AccessHow to select the Corners ?1. Push the cursor key ↑ or ↓ to highlight the Coarse selection. (menu 6-57)2. By default corner is already

6. Random AccessHow to adjust the Corners ?1. Push the cursor key ↑ or ↓ to select pixel x = 0 in the Geom etry Distortion menu. (menu 6-58)2. Push th

6. Random AccessImage 6-19Corner pixel y adjustmentImage 6-20Keystone correction6.5.7.3.4 Side Bow selectionWhat can be done ?With the Coarse Side Bow

6. Random AccessHow to select the Side Bows ?1. Push the cursor key ↑ or ↓ to highlight the Coarse selection. (menu 6-60)2. Press ENTER to scroll thro

6. Random Access6.5.7.3.5 Bow shaped pre-distortion set upHow to set up a bow shaped pre-distortion ?We assume side bow top is selected.1. Push the cu

6. Random AccessBy pressing the * key on the RCU an internal hatch pattern is projected instead of the image data.Howtoperformacoarselinearityadjustme

6. Random Access6.5.7.3.7 Center selectionWhat can be done ?With the Coarse Center selection it is possible to perform a coarse bow correction on the

6. Random Access5. Use the subpixel adjustments to fine shift the Center.6. When the Coarse adjustment is finished press EXIT to return to the Guided

6. Random Access6.5.7.4.2 Horizontal or Vertical Linearity selectionWhat can be done with the Linearity adjustment ?Within this Linearity adjustment m

Table of contents4 R5976781 TRACE+ 14/09/2004

6. Random AccessImage 6-27Horizontal Linearity coarse adjustmentImage 6-28Horizontal Linearity right adjustmentImage 6-29Horizontal Linearity center a

6. Random Access6.5.7.4.4 Vertical Linearity adjustmentHow to adjust the Vertical Linearity ?A correct Vertical Linearity is achieved when the distanc

6. Random AccessImage 6-31Vertical Linearity bottom adjustmentImage 6-32Vertical Linearity center adjustment6.5.7.5 FineOverview•Startup• Horizontal o

6. Random Access6.5.7.5.1 Start upHow to Start up the Fine adjustment ?1. Push the cursor key ↑ or ↓ to highlight Fine in the Edit menu. (menu 6-75)2.

6. Random AccessImage 6-33Fine horizontal or vertical linearity selections6.5.7.5.3 Fine Horizontal or Vertical Linearity adjustmentHow to adjust the

6. Random AccessImage 6-34Fine horizontal or vertical linearity adjustment6.5.7.5.4 Bow Linearity selectionWhat can be done ?Within this menu it is po

6. Random AccessImage 6-35Fine bow linearity selections6.5.7.5.5 Bow Linearity adjustmentHow to adjust the Bow Linearity ?We assume bow top is selecte

6. Random AccessImage 6-36Fine bow linearity adjustments6.5.7.5.6 Quadrant selectionWhat can be done ?Within this menu it is possible to perform a fin

6. Random AccessImage 6-37Fine quadrant selections6.5.7.5.7 Quadrant adjustmentHow to adjust Quadrants ?We assume quadrant top left is selected.1. Pus

6. Random AccessImage 6-38Fine quadrant adjustments6.5.7.5.8 Local selectionWhat can be done ?Within this menu it is possible to smooth away bumps and

1. Safety Instructions1. SAFETY INSTRUCTIONS1.1 WarningsTo prevent personnel injuryThe customer should never attempt to disassemble the lamp casing or

6. Random AccessImage 6-39Fine local grid point selections6.5.7.5.9 Local adjustmentHow to adjust the Local grid points ?1. Push the cursor key ↑ or ↓

6. Random Access6.5.7.6 ShiftWhat can be done with the Shift adjustment ?With Shift adjustment it is possible to shift the whole image.How to Start up

6. Random AccessImage 6-41Transport Delay basic principleHow to Start up the Transport Delay ?1. Push the cursor key ↑ or ↓ to highlight Transport Del

6. Random Access7. Repeat step 3 to 6 for projector 3.8. Press EXIT to return to the Guided G eometry Map menu.TRANSPORT DELAYMODE [AUTOMATIC]TRANSPOR

6. Random Access6.5.7.8.2 Blanking Active OnHowtoswitchBlankingActiveOn?1. Push the cursor key ↑ or ↓ to highlight Active in the Blanking/Soft Edge me

6. Random AccessImage 6-42Shape selections6.5.7.8.5 Blanking adjustmentWhat is % of image and %% of image adjustment ?% of image Coarse adjustment, th

6. Random Access5. Press EXIT to return to the Guided G eometry Map menu.6. Press EXIT to return to the Edit menu.SHAPEtop left% of image = 0%% of ima

6. Random AccessImage 6-43WhySoft Edge ?What is the Basic Principal of Soft Edge ?The principle of edge blending is archived by linear modulation of t

6. Random Access6.5.7.9.3 Soft Edge Start upHow to Start up Soft Edge ?1. Push the cursor key ↑ or ↓ to highlight Blanking/Soft Edge menu. (menu 6-107

6. Random Access6.5.7.9.6 Soft Edge Shape selectionsHow the use the Soft Edge Shape selection ?1. Push the cursor key ↑ or ↓ to highlight the first it