Barco MDRC-1119 User Manual

MDRC-1119 MDRC-1119 TS MDRC-1119 HB MDRC-2120 User manual

External equipment External equipment intended for connection to signal input/output or other connectors, shall comply with relevant UL/ EN/ IEC s

Installation Place the display on a flat, solid and stable surface that can support the weight of at least 3 displays. If you use an unstable ca

screen saver is not activated), change the image content regularly to avoid image retention of the static elements. 3. Understand pixel technology

display and components carefully, then set up and handle the unit properly to avoid damage to the LCD panel. • Use both hands to grasp the displa

• Unplug the power cord from the wall outlet during thunderstorms. • Do not place magnetic devices, such as motors, near the display. Cleaning t

Before returning the display to the container, do the following: 1 Swivel the display panel in landscape mode. 2 Push the panel down to the lowest

Explanation of symbols DISPOSAL. Do not use household or municipal waste collection services for disposal of electrical and electronic equipment.

Introduction About the product Thank you for choosing Barco. The MDRC series are LCD displays with an active matrix, thin-film transistor (TFT)

MDRC-2120 • Dual Analog and Digital signal. • 20.1” diagonal Screen. • 1600x1200 high resolution. • Wide Viewing Angle Technology. • 31.5 ~ 9

Package Overview USA Power Cord EUR Power Cord C

Copyright notice This document is copyrighted. All rights are reserved. Nor this document, nor any part of it, may be reproduced or copied i

Installation Product Overview Front View 20

Back View MDRC-1119 / MDRC-1119 TS / MDRC-1119 HB MDRC-2120 DC Power-In USB Ports DVI-D Input VGA Input DC Power-In USB Ports DVI-D In

Tilt Grasp the LCD Display with both hands and adjust the tilt as desired. Kensington Security Slot The Monitor can be secured to your desk or

Start Your Installation Connecting the Display Use only the power adapter which are the forming part of each medical device, the power cord, and

than or equal to the native resolution, and make sure the timing of the display mode is compatible with the LCD screen. We have listed the “Compat

Adjusting the screen position Vertical Height Portrait/Landscape Left to Right Pan Front to Back Tilt Remove Monitor Stand may forcefully

User Controls Jog Dial Controls   26

No./ Icon Control Function  Jog Dial button - Power Switch - Menu 1. Press the jog dial button for 1 sec to power off to the LCD Displ

On-Screen Display Menus Main Menu Function Description Input Selection Go to the ‘Input Selection Menu’ while the jog-dial button is pressed. Ad

Color Go to the ‘Color Menu’ while the jog-dial button is pressed. Geometry* Go to the ‘Geometry Menu’ while the jog-dial button is pressed. Set

Table of Contents Table of Contents ... 3 Preface ...

Input selection Menu Function Description DVI Select the DVI input while the jog-dial button is pressed. VGA Select the VGA input while the jo

Adjustments Menu Function Description Brightness To adjust the backlight luminance.. Contrast** To adjust the image contrast (only applica

Adjustments -> Gamma menu Function Description Native Select the panel original gamma. Gamma 1.8 Select the Dynamic Gamma 1.8. Gamma 2.2

Color Menu Function Description Native Select the panel original color temperature. Clearbase Set the image color temperature to Clearbase B

Exit Close this menu. Color Menu -> User Menu Function Description Red Turn red gain value manually. Green Turn green gain value manually.

Geometry Menu** Function Description Auto set Adjust the image parameters to obtain a correctly aligned image automatically while the jog-dial

Horizontal position Adjust the image horizontal position manually. Vertical position Adjust the image vertical position manually. Exit Close th

Setting Menu Function Description OSD Setting Go to the ‘OSD Settings menu’ while the jog-dial button is pressed. Factory Reset Go to the ‘F

Power Save Go to the ‘Power Save Menu’ while the jog-dial button is pressed. LED Go to the ‘LED Menu’ while the jog-dial button is pressed. Back

Settings Menu -> OSD Settings Menu Function Description OSD Timeout Set the OSD timeout value. OSD Horizontal Set the OSD horizontal alig

Technical specifications MDRC-2120 ... 58 Compatibility Modes MDRC-2120 ...

Settings Menu -> OSD Settings Menu -> OSD Direction Function Description Landscape Select OSD Landscape. Portrait Select OSD Portrait. B

Settings Menu -> Factory Reset Menu Function Description Yes Execute the ‘Factory Reset’. No Abort the ‘Factory Reset’. Back Go back to th

Settings Menu -> Factory Reset Menu Function Description English Execute the ‘Factory Reset’. Français Select 'Français' as the

Settings Menu -> Power Save Menu Function Description On Enable the ‘Power Save’ function. Off Disable the ‘Power Save’ function. Back Go

Settings Menu -> LED Menu Function Description On Enable the LED. Off Disable the LED. Back Go back to the ‘Settings Menu’. Exit Close th

Information Menu Function Description FW version Firmware version System hours System run time Backlight run time Backlight run time Back G

Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following troubleshooting. If the problem persists, pl

Problem: Image is unstable and flickering • Use “Phase” to make an adjustment. Problem: Image is scrolling • Check and make sure the VGA signal

Product Dimensions MDRC-1119/MDRC-1119 TS/MDRC-1119 HB 48

Technical specifications MDRC-1119 Product MDRC-1119 Technology TFT Color LCD (VA) Native resolution 1280 x1024 Active screen diagonal 19&quo

Preface Important notice Notice Although every attempt has been made to achieve technical accuracy in this document, we assume no responsibility f

OSD languages English, French, German, Spanish, Italian, Dutch, Simplified Chinese, Traditional Chinese, Korean. Options Protective Cover Yes

Power consumption 50 Watts Environmental Operational temperature range within specs +15°C to +35°C Storage & transport temperature -20°C

Aspect ratio 5:4 Viewing angle (CR>10) 178°/178° Display LUT 10 bit Response time (G-G) 8 ms Display Functions Gamma, Dicom Colors 1

Display weight With Stand : 9.39 kg Without Stand : 6.29 kg Display stand Tilt, height & swivel Mounting VESA 100x100 WARNING:

Technical specifications MDRC-1119 HB Product MDRC-1119 HB Technology TFT Color LCD (VA) Native resolution 1280 x1024 Active screen diagonal

Options Protective Cover No Touch Screen No Landscape/Portrait Yes Certifications EMC EN 60601-1-2; FCC-B; ICES-001, VCCI, KC, CCC, BSMI S

Environmental Operational temperature range within specs +15°C to +35°C Storage & transport temperature -20°C to +60°C Operating humidity

VESA XGA VESA XGA 1152x870 1152x864 60 75 54.36 68.1 VESA SXGA VESA SXGA 1280x1024 1280x1024 60 75 63.96 79.95 Apple Mac II Apple M

Technical specifications MDRC-2120 Product MDRC-2120 Technology TFT Color LCD (IPS) Native resolution 1600 x1200 Active screen diagonal 20.1&

OSD languages English, French, German, Spanish, Italian, Dutch, Simplified Chinese, Traditional Chinese, Korean. Options Protective Cover Yes

Environmental information Disposal Information The lamps inside the display contain mercury. Do not throw the display in the trash. Dispose of it

Power consumption 55 Watts Environmental Operational temperature range within specs +15°C to +35°C Storage & transport temperature -20°C

Regulatory Compliance Canada, European Union, United States This display has been tested and found to comply with IEC/EN 60601-1 and IEC 60601-1-2

The display was classified as required by the MDD according to Annex IX of the directive and the medical device (MEDDEV) guidance available at the

EU EMC Directive 2004/108/EC EU Electromagnetic Compatibility Directive EN 60601-1-2 (2007) Collateral standard electromagnetic Medical Electrica

IEC 61000-4-6 Conducted immunity IEC 61000-4-8 Magnetic field immunity Conformance to the Medical Device Directive 93/42/EEC EN 60601-1 Medica

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienc

66

67

B4100531-07 October 2014 Barco nv President Kennedypark 35 8500 Kortrijk Belgium www.barco.com

China Energy Label If there is a China Energy Label on your packaging or product, the product meets the following energy requirements correspondin

Electrical shock Warning- To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture Warning- Please do n

The unit is not intended to be used in any life support system and diagnosis. Power connection Power requirements: The display must be powered usi