Barco Nio 5MP User Manual

Installation & User ManualNio 5MP

Safety Instructions10• Do not overload wall outlets and extension cords as this may result in fire or electric shock.• Mains lead protection (U.S.: Po

Safety Instructions11• Switch on DPMS on display and PC • Activate a good screen saver

Explanation of symbols12Explanation of symbolsSymbols on the display and/or power supplyOn the display or power supply, you may find the following sym

13Overview

Overview(This page intentionally left blank.)14(This page intentionally left blank.)

Introduction15IntroductionThank you for choosing Barco.Single display or complete system?This manual describes installation and usage of a complete Ni

Introduction16Power savingThe display is equipped with a power saving system. When left idle for a certain time, the computer connected to the display

Display controller information17Display controller informationMinimum System Requirements• Pentium II 266 MHz with 128 MB RAM (Pentium 800MHz with 256

Display controller information18The following resolution is also available when the OS is booted in VGA mode.• 640x480 @ Default Refresh Rate, 16 colo

Package contents19Package contentsNio System packageEach Nio system contains one or more display boxes (see below) and a system accessory box containi

(This page intentionally left blank.)2(This page intentionally left blank.)

Parts, controls and connectors20Parts, controls and connectorsFrontFigure 11. Power LEDThe LED is off when the display is disconnected from the power.

Parts, controls and connectors21RearFigure 21. Connector compartment coverTo get access to the connectors, remove the cover by pulling down the 2 clip

Parts, controls and connectors22Connect the external power supply, delivered with the display, to this connector.8. Tilt & swivel foot strapThe di

Parts, controls and connectors231. Video 1 output2. Video 2 output3. VGA boot on/off jumper4. PCI connector

Parts, controls and connectors(This page intentionally left blank.)24

25Installation

Installation(This page intentionally left blank.)26(This page intentionally left blank.)

Installation27Precautions• Keep your original packaging. It is designed for this display and is the ideal protection during transport.• Avoid reflecti

Display Controller installation28Display Controller installationCaution: Wear a protective ESD strap during installation or handling of the display co

Display Controller installation29Figure 5If you decide to use a separate VGA monitor as your boot monitor, you must disable the BarcoMedNio’s on-board

3Preface

Display Controller installation30Figure 6: PCI and RAID Controller SlotsInstalling the BarcoMed Nio display controllerInstall the BarcoMed Nio control

Display Controller installation31connect the secondary display to the other connector on the display controller.7. Reconnect the power cord, turn on t

Display installation32Display installationAfter unpacking the displayImportant:In the factory, the height-positioning system in the display foot is bl

Display installation33To change the panel orientation:1. Stand at the front side of the panel and take the panel at both sides.2. Very important: Tilt

Display installation344. To change from landscape to portrait, turn clockwise.Notice: Before installing the Nio driver, put the display panel in portr

Display installation35Figure 124. Connect the other end of the power cord to a grounded power outlet.We recommend to use an additional surge protector

Display installation362. Connect the second display to Vid 2 (Head B).Figure 14USB connectionConnecting the display to the PC via USB is not necessary

Display installation37Figure 15Cable routingRouting the signal cables• Bind the cables in the connector compartment together with the cable tie inside

Display installation38To put the foot cover in place:Figure 16: 1. The foot cover is packaged separately in the accessory box. Unpack the foot cover.2

Attaching the display to an arm39Attaching the display to an armThe panel, standard attached to the tilt & swivel foot, is compatible with the VES

Preface(This page intentionally left blank.)4(This page intentionally left blank.)

Attaching the display to an arm406. Remove the four screws fixing the foot while supporting the foot.7. Attach the arm stand firmly to the panel using

Software installation41Software installationInstalling the BARCOMED display controller drivers and softwareNote: The installation dialog will display

Software installation42c) Click Browse and browse to the root directory of the BARCO MEDICAL IMAGING DISPLAY SYSTEM CD-ROM and click on the file, Setu

Software installation436. When the driver setup is complete, click the Finish button.The Barco Product Installation Wizard will now guide you through

Software installation44Command line (Silent) Install of Drivers and SoftwareSpecifying the silent install option causes most of the GUI associated wit

Software installation45Figure 20

Settings for optimal display performance throughout the product lifetime46Settings for optimal display performance throughout the product lifetimeAvoi

Settings for optimal display performance throughout the product lifetime47To activate appropriate screen saving, proceed as follows:1. In the display

Settings for optimal display performance throughout the product lifetime(This page intentionally left blank.)48

49Operation

Preface5CopyrightThis document is copyrighted. All rights are reserved. Nor this document, nor any part of it, may be reproduced or copied in any fo

Operation(This page intentionally left blank.)50(This page intentionally left blank.)

BarcoMed control panel operation51BarcoMed control panel operationThis chapter describes how to configure the displays in your Barco Medical Imaging D

BarcoMed control panel operation52Figure 21 Barco TabBarco System ReportThe Barco System Report, also known as BarcoMed SelfExam, is a wizard based to

BarcoMed control panel operation53Advanced PropertiesTo access the advanced properties configuration pages for your Barco display controller(s), click

BarcoMed control panel operation54applications that are designed to work correctly with 8-bit (256-color) modes should continue to work normally.Note:

BarcoMed control panel operation55Enable DitheringThis option allows the user to enable or disable dithering. Dithering is a technique for increasing

BarcoMed control panel operation56Internationale de I’Eclairage) model will be adapted, which weights the colors as 59% Green, 30% Red, 11% Blue.Monit

NioWatch operation57NioWatch operationTo use NioWatchThe NioWatch application resides in the Windows systray. To use one of the NioWatch functions, ri

NioWatch operation58• To select another display function, select an item from the Display Function drop-down box.If you select DICOM Optimized, you wi

NioWatch operation59Test PatternsFigure 24• Select the desired test pattern and click Show to display the pattern.• If you select Custom Image, you ca

Preface6instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cau

Display operation60Display operationStand-by switchingWhen the display is on and no on-screen display is visible, push the control wheel at the front

Display operation61How to navigate through the on-screen display1. To display the on-screen menus, rotate the control wheel.2. To enter into a menu or

Display operation623. Press the control wheel to enter the Settings menu.Figure 27: Settings menu4. Rotate the control wheel to select User Controls.5

Display operation63Complete OSD overviewMain menuLuminanceSettingsName DescriptionLuminance Adjust the target luminance to which the dis-play will be

Display operation64Information Name DescriptionProduct The display typeSerial No Indicates the display serial numberSW Version Displays the current in

65Cleaning

Cleaning(This page intentionally left blank.)66(This page intentionally left blank.)

Cleaning67Precautions• Take care not to damage or scratch the glass or LCD panel.• Do not apply pressure on the glass or LCD panel.• Do not apply or s

Cleaning68particles and other dry contaminants on the surface of the lcd panel or the glass panel.Attention: The dust remover contains a liquid gas. I

69Troubleshooting

Table of Contents7Table of ContentsPreface ...3Safety Instructions..

Troubleshooting(This page intentionally left blank.)70(This page intentionally left blank.)

Troubleshooting71General tips• If one display from a multi-head system exhibits problems, try to eliminate the problem by switching video cables or po

Troubleshooting72Problems and solutionsProblem description Possible tests or solutionsScreen remains black • Please check the installation procedure i

Troubleshooting73The PC does not start up • Check the CMOS settings in the PC BIOS• The display controller may not be firmly seated in the PCI connect

Troubleshooting74Setting the resolution of your BarcoMed Nio displayIn order to set or change the resolution of your Nio display you must be logged in

Troubleshooting75the “Extend my Windows desktop onto this monitor” checkbox, but do NOT click the “Apply” button at this time.If you installed your Ba

Troubleshooting76press the “TAB” key once and then press “CTRL”+“Enter” to select “OK”.7. Click “OK” in the “Windows will now apply your new desktop s

Troubleshooting77Figure 29: The Windows Display Properties Control Panel Settings Tab after the drivers have been installed and the resolution set wit

Troubleshooting78minutes, browse the contents of your Nio Software CD and double click on the file: “Setup.exe” to start the wizard.The wizard will be

Troubleshooting79Uninstalling the BarcoMed Nio driver1. Insert your BarcoMedNio Software CD into your computer’s CD drive.2. The BarcoMed Product Inst

Table of Contents8Display operation ... 60Stand-by switching...

Troubleshooting80Figure 326. Click “Next”.7. If you installed your driver with DualView enabled, skip to 8.If you installed your driver with DualView

Troubleshooting819. Click “Reboot” to disable DualView, click “Finish” and then click “Yes” to reboot your system.10. When your system restarts, log i

Troubleshooting823. Insert your BarcoMedNio Software CD into your computer’s CD drive.4. The BarcoMed Product Installation Wizard will display its wel

83Technical Information

Technical Information(This page intentionally left blank.)84(This page intentionally left blank.)

Technical specifications85Technical specificationsE-5420:Item SpecificationPicture panel 20.1-inch Advanded-SFTResolution Native: 2560 x 2048Display a

Technical specifications86Dimensions (W x H x D) In perpendicular vertical position, highest position, tilt = 0°, swivel = 0°:382 x 589 x 212 mmNet we

Connector pin assignments87Connector pin assignmentsDVI connector:Pin no. Signal Pin no. Signal1 TMDS DATA 2- 14 +5V POWER2 TMDS DATA 2+ 15 GND3GND 16

Glossary88GlossaryCalibrationEach display is calibrated in the factory before it is sent to the customer. After this calibration, black and white lumi

Glossary89DICOMDICOM stands for Digital Imaging and Communications in Medicine. It is a standard developed by the American College of Radiology (ACR)

Safety Instructions9Safety InstructionsGeneral RecommendationsRead the safety and operating instructions before operating the display. Retain safety a

Glossary(This page intentionally left blank.)90

91Warranty Statement

Warranty Statement(This page intentionally left blank.)92(This page intentionally left blank.)

Warranty Statement93ARTICLE 1: SERVICESBarcoView warrants that the equipment will be free of defects in workmanship or material for the warranty perio

Warranty Statement94ARTICLE 2: ITEMS EXCLUDED FROM WARRANTYThe warranty described herein shall not include the following:2.1 Any hardware or software

Warranty Statement95agents, employees, or representatives, shall be borne by the Customer at its additional cost and expense.3.3 The customer is respo

Warranty Statement96this agreement is impeded by reason of force majeure. For the purposes of this clause the expression “force majeure” means, but sh

Warranty Statement97

Warranty Statement98

www.barco.comB4100447-06March 2007