Barco CINE7 R9010040 Installation Manual

HOM E CINEMABAR CO CINE7R9010040R9010050INSTALLATION MANUAL26022003 R5976585/00

1. Safety Instructions6 R5976585 BARCO CINE 7 26022003

2. Packaging and Dimensions2. PACKAGING AND DIMENSIONS2.1 Projector PackagingWay of PackagingThe projector is packed in a carton box. To provide prote

2. Packaging and DimensionsImage 2-28 R5976585 BARCO CINE 7 26022003

3. Installation Guidelines3. IN STALLATION GUIDELINESOverview• General Installation Guidelines• Configuration• Lens Formulas• Scan Adaptation3.1 Gener

3. Installation GuidelinesScreens are rated by how much light they reflect ( or transmit in the case of rear projection systems) g iven a determined a

3. Installation GuidelinesImage 3-2Possible configurationsPositioning the projectorThe projector should be installed p erpendicular with the screen on

3. Installation GuidelinesImage 3-3Projector positioningB Distance between c eiling and top of the screenA Correction value, extra v alue to be added

3. Installation Guidelines3.4.1 Access to the scan controlsHow to get access1. Turn both lock screws with a sc rewdriver or a coin counter clockwise.2

3. Installation GuidelinesImage 3-6Chassis o penImage 3-7Removing the top co ver3.4.2 Scan InversionHorizontal scan inversionThree connectors are used

3. Installation GuidelinesImage 3-8Scan connectorsVertical Scan InversionThree connectors are used, one for each vertical deflection coil. W hen ch an

Barco nv Home CinemaNoordlaan 5, B-8520 KuurnePhone: +32 56.36.84.30Fax: +32 56.36.88.62E-mail: [email protected] us at the web: www

3. Installation GuidelinesCheck procedureThis c heck procedure can only be done after power (mains) connection. So, first continue with the projector

4. Projector Set up4. PROJECTOR SET UPOverview• Password strap4.1 Password strapWhat is allowed?With a strap on the controller unit, the important pro

4. Projector Set upImage 4-218 R5976585 BARCO CINE 7 26022003

5. Installation Adjustment5. INSTALLATION ADJUSTMENTOverview• Entering the Service menus• Starting up the Installation Adjustment Mode• Password Prote

5. Installation AdjustmentImage 5-15.2 Starting up the Installation Adjustment ModeHow to Start Up the Installation Adjustment Mode?1. Push the cursor

5. Installation AdjustmentEntering the Password w ith the RCUThe Password contains 4 digits, when the projector asks to enter your password:1. Enter t

5. Installation AdjustmentNecessary toolsnutdriver 11 mm or screwdriverSet up the sc heimpflug range1. Open the top cover, see Installation Guidelines

5. Installation Adjustment5.6 Optical Lens FocusingWhat can be done?The optical focusing procedure is performed separately for each lens. The appropri

5. Installation AdjustmentImage 5-4Electri cal focus adjustmentThe blue focus has been factory adjusted for optimal color reproduction. Readjus tment

5. Installation AdjustmentImage 5-5CRT Phosphor WidthHow to center the raster?1. Press the ENTER key to activate the raster on the Green CRT facep lat

Copyright ©All rights reserved. No part of this documen t m ay be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or

5. Installation AdjustmentCRT PROJECTION ANGLEADJUSTMENTCRT PROJECTION ANGLE IS THEFIRST STEP OF STATICCONVERGENCE ADJUSTMENTIT IS CRITICAL THAT THERA

5. Installation AdjustmentImage 5-7CRT angle correctionImage 5-8Red CRT Projection Angle AdjustmentImage 5-9Red CRT Projection Angle AdjustmentR597658

5. Installation Adjustment28 R5976585 BARCO CINE 7 26022003

6. G2 Adjustment6. G2 ADJUSTMENT6.1 Sta rt up the G2 adjustmentStart up1. Enter the adjustment m ode by pre ssing ADJU ST. (menu 6-1)2. Highlight Serv

6. G2 AdjustmentImage 6-1The best resu lt is obtained in a completly dark ro om or by looking into the lenses, but be aware that b rightnessand contra

Revision SheetTo:Barco nv Home Cinema/Docum entationNoordlaan 5, B-8520 KuurnePhone: +32 56.36.84.30, Fax: +32 56.36.88.62E-mail: antoon.de jaegher@ba

Table of contentsTABLE OF CON TENTS1. Safety Instructions...

Table of contents2 R5976585 BARCO CINE 7 26022003

1. Safety Instructions1. SAFETY INSTRUCTIONSOverview• Safety Instructions1.1 Safety InstructionsNotice on SafetyThis equipment is built in accordance

1. Safety Instructionsin a residential area is likely to cause harmful interference in which case the us er w ill be required to correct the interfere

1. Safety InstructionsOn Installation• Do not place this equipment on an unstable c art, stand, or table. The pro duct may fall, causing serious damag