Barco CLM HD8 R9050130 User Manual Page 118
- Page / 231
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
11. Lamp menu
11.5 Status and run time overview lamps
Overview
1. Press MENU to activate the menus.
2. Use the ▲ or ▼ key to select Lamp and press ENTER.
3. Use the ▲ or ▼ key to select Overview and press ENTER.
The status and the run time for each lamp are displayed.
Image 11-11
Image 11-12
Image 11-13
11.6 Lamp mode
What can be done?
In 4 lamps mode, the projector will always ignite all 4 lamps.
In 2 lamps mode, the projector will always ignite lamp 1 & 3 or 2 & 4 depending on the current run time. It will always use those with
the lowest run time.
In 1lampmode, the projector will always ignite lamp 3 or 4, depending on the current run time. It will always use the lamp with the
lowest run time.
How to change the lamp mode
1. Press MENU to activate the menus.
2. Use the ▲ or ▼ key to select Lamp and press ENTER.
3. Use the ▲ or ▼ key to select Lamp mode and press ENTER.
The Lamp mode selection menu is displayed.
4. Use the ▲ or ▼ key to select the desired lamp mode and press ENTER.
Image 11-14
Image 11-15 Image 11-16
114 R59770057 CLM HD8 15/03/2010
- User guide 1
- GNU-GPL code 4
- Disposal Information 4
- TABLE OF CONTENTS 5
- Table of contents 6
- 1. SAFETY 9
- 1. Safety 10
- 1.3 Recycling guidelines 12
- 2. GENERAL 15
- 2.2 Unpacking the projector 16
- 2.3 Box content 17
- 2.4 Projector configurations 18
- 2. General 19
- 3. PHYSICAL INSTALLATION 23
- 3. Physical installation 24
- 3.2 Lenses 27
- 4. STACKING CLM PROJECTORS 35
- 4. Stacking CLM projectors 36
- Inclination 38
- 5. CONNECTIONS 39
- 5. Connections 40
- 6. GETTING STARTED 47
- 6. Getting started 48
- 6.3 Operating the projector 49
- 6.4 Using the RCU 51
- 6.5 Quick setup adjustments 52
- Quick shift adjustment 53
- 6.6 Use of the AUTO button 55
- 6.7 Projector Address 55
- 6.8 Source selection 57
- 6.9 Controlling the Projector 57
- 7.1 About the adjustment mode 59
- How to make an adjustment? 60
- R59770057 CLM HD8 15/03/2010 61
- 8. INPUT MENU 63
- 8. Input menu 64
- 8.3 Input locking 65
- 8.4 Minimum delay 67
- 8.5 Native resolution 67
- 8.6 Source switching 69
- 8.7 No signal 69
- 9. IMAGE MENU 73
- 9.3 Image Settings 74
- 9. Image menu 75
- 9.3.9 Input balance 82
- Analog Digital Conversion 82
- 4/3 signal 86
- 16/9 RGB signal 86
- 9.5 Timings 87
- 9.6 Image files services 92
- 9.7 Save custom settings 97
- 10. LAYOUT MENU 99
- 10. Layout menu 100
- 10.3 PIP window 104
- 10.4 Layout file services 110
- 11. LAMP MENU 115
- 11.3 Lamp power 116
- 11.4 Lamp Identification 117
- 11.6 Lamp mode 118
- 12. ALIGNMENT MENU 119
- 12.2 Orientation 120
- 12.3 Lens adjustment 121
- 12.4 Side keystone 122
- 12.5 Blanking 123
- 12.6 Intensity 124
- 12.7 Gamma 124
- 12.8 Internal pattern 125
- 12.9 Color space 126
- 12.10 White peaking 127
- 12.11 ScenergiX 128
- 12. Alignment menu 129
- 13. PROJECTOR CONTROL 139
- 13.2 Projector address 140
- 13.3 Serial communication 141
- 13. Projector control 142
- 13.4 Network 143
- 13.5 IR control switching 147
- 13.6 DMX 148
- 13.7 Buttons 152
- 13.8 Menu position 153
- 13.9 Local LCD contrast 154
- 13.10 Language selection 154
- 14. SERVICE MENU 157
- 14. Service menu 158
- 14.3 Diagnosis 159
- 14.5 Restore factory defaults 164
- 14.6 Save custom settings 165
- 14.7 Refill mode 166
- 14.8 USB memory 167
- 15. MAINTENANCE 171
- 15. Maintenance 172
- 16. SERVICING 173
- 16. Servicing 174
- 16.3 Lens installation 175
- 16.4 Lens removal 176
- 16.5 Removal of a lamp unit 177
- 16.6 Mounting a new lamp unit 179
- INSTALLATION 185
- 17.2 Removal of the lamp door 186
- Necessary tools 187
- How to remove the back cover 187
- 17.4 Removal of the top cover 188
- How to install 189
- How to install the lamp door 192
- Image 17-18 193
- Secure the lamp door 193
- A.1 Dimensions of the CLM HD8 195
- A. Dimensions 196
- 532145.5 196
- B.1 Table overview 197
- B. Standard Source Files 198
- C. DMX CHART 199
- C.2 CLM control cha 200
- C. DMX Chart 201
- D. SPECIFICATIONS 203
- D. Specifications 204
- E. TROUBLESHOOTING 209
- E. Troubleshooting 210
- About this chapter 215
- Overview 215
- What has to be done? 216
- F.3 Preparing the projector 217
- F.4 Mounting the carry handle 218
- Use a 2,5 mm Allen wrench 219
- G. ORDER INFO 221
- G. Order info 222
- GLOSSARY 223
- Glossary 224
- Revision Sheet 231
Related products and manuals for Projectors Barco CLM HD8 R9050130
Projectors Barco R9000977 User Manual
(60 pages)
(60 pages)
Projectors Barco R9001870 User Manual
(31 pages)
(31 pages)
Projectors Barco R9001490 User Manual
(93 pages)
(93 pages)
Projectors Barco R5976924 User Manual
(245 pages)
(245 pages)
Projectors Barco R59770449/01 User Manual
(79 pages)
(79 pages)
Projectors Barco CLM R10+ User Manual
(229 pages)
(229 pages)
Projectors Barco R9001960 User Manual
(127 pages)
(127 pages)
Projectors Barco R9010570 User Manual
(106 pages)
(106 pages)
Projectors Barco R9002790 User Manual
(83 pages)
(83 pages)
Projectors Barco R5976562 User Manual
(135 pages)
(135 pages)
Projectors Barco 1280 User Manual
(26 pages)
(26 pages)
Projectors Barco R9002031 User Manual
(45 pages)
(45 pages)
Projectors Barco R9001769 User Manual
(57 pages)
(57 pages)
Projectors Barco R9001070 User Manual
(121 pages)
(121 pages)
Projectors Barco ID LR-6 R9010342 User Manual
(135 pages)
(135 pages)
Projectors Barco R9010111 User Manual
(51 pages)
(51 pages)
Projectors Barco R9010010 User Manual
(137 pages)
(137 pages)
Projectors Barco R9010310 User Manual
(135 pages)
(135 pages)
© 2020, manymanuals.com. All rights reserved. | 1.364 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals