Barco Coronis Elite Specifications

Getting Started GuideCoronisSupported displays:MDCC 2121, MDCG 2121, MDCG 3120

CE mark notice10CE mark noticeDeclaration of Conformity in accordance with Article 10 (1) of the CE directiveThis product has been designed and manufa

Barco nvPresident Kennedypark 358500 KortrijkBelgiumwww.barco.comB410578-05April 2013

Environmental information11Environmental informationDisposal InformationThis product consists of devices that may contain mercury, which must be recyc

Environmental information12Information for China ROHS complianceTable of toxic and hazardous substances/elements and their content, as required by Chi

Environmental information13LCD Monitor 　　　　 　 　零部件名稱 有毒有害物質或元素　铅（Pb）汞（Hg）镉（Cd）六价铬（Cr6+）多溴联苯（PBB）多溴二苯醚（PBDE）金属机构件 O O O O O O塑料机构件 O O O O O O电路板组件 * O

Safety Instructions14Safety InstructionsGeneral RecommendationsRead the safety and operating instructions before operating the display. Retain safety

Safety Instructions15Power connection - display with external power supply• Power requirements: The display must be powered using the delivered medica

Safety Instructions16Installation Place the display on a flat, solid and stable surface that can support the weight of at least 3 displays. If you use

EMC notice17EMC noticeNo specific requirement on the use of external cables or other accessories except power supply.With the installation of the devi

EMC notice18must accept any interference received, including interference that may cause undesired operation.Interference can be determined by turning

EMC notice19UT is the a.c. mains voltage prior to application of the test levelVoltage dips, short interruptions and voltage variations on power suppl

(This page intentionally left blank.)2(This page intentionally left blank.)

EMC notice20a Field strengths from fixed transmitters, such as base stations for radio (cellu-lar/cordless) telephones and land mobile radios, amateur

EMC notice21sured field strength in the location in which the BARCO CORONIS Display is used exceeds the applicable RF compliance level above, the BARC

EMC notice22For transmitters rated at a maximum output power not listed above, the recom-mended separation distance d in meters (m) can be estimated u

Explanation of symbols23Explanation of symbolsSymbols on the display and / or power supplyOn the display or power supply, you may find the following s

Explanation of symbols24Symbols used throughout the manual:Indicates the display serial no.Consult the operating instructionsIndicates this apparatus

Recommendations for using your display system25Recommendations for using your display system1. Optimize the lifetime of your displayEnabling the Displ

Recommendations for using your display system26diagnostic performance of the product. To ensure optimal product quality, Barco applies strict selectio

Display controller installation27Display controller installation

Display Controller Installation28Display Controller InstallationWhich display controller?Your Barco medical display is compatible with a large range o

Display Controller Installation29Types of display controllers for Barco Display SystemsThe following models of Barco display controllers are available

3Copyright noticeThis document is copyrighted. All rights are reserved. Neither this document, nor any part of it, may be reproduced or copied in an

Display Controller Installation30Figure 1: Display controller VGA Jumper, VGA enabledNote: To use multiple BarcoMed display controllers in a single co

Display Controller Installation31Installation ProcedureThe following instructions will take you step by step through the installation of the display c

Display Controller Installation327. Align the display controller(s) for your BARCO CORONIS Display System with the slot(s) and press it(them) in firml

Display Controller Installation339. Screw in or fasten the display controller securely. Replace and secure the computer cover.10. Connect your BARCO C

Display Controller Installation34Figure 7: Note: For 6mp, connect Head 1 to left input, and Head 2 to right input.Figure 8: IO-Panel for the Barco MXR

Display Controller Installation35Note: For 6mp, connect Head 1 to left input, and Head 2 to right input.Figure 9: Note: Disconnecting the DisplayPort

Display Controller Installation3612. Turn on the display(s) and then your computer.Turning on your systemIf you have properly installed your graphics

Display installation37Display installation

Installation precautions38Installation precautionsPrecautions• Keep your original packaging. It is designed for this display and is the ideal protecti

Display parts, controls and connectors39Display parts, controls and connectorsFrontThe front controls are soft touch keys.When you touch any of them w

4Indications for useThe Coronis displays are intended to be used in displaying and viewing digital images for review and analysis by trained medical p

Display parts, controls and connectors40To display the OSD (on-screen display). In the OSD, this button acts as Enter button to make selections.4. Sta

Display parts, controls and connectors41RearFigure 12: Rear view1. Connector compartment cover.Detach to get access to the signal connectors.2. Slot f

Display parts, controls and connectors42Connect the output of the DC power supply delivered with the display to this connector.2. +5 Vdc, 0.25 A power

Display parts, controls and connectors43FootThe display stand is packaged separately from the display panels. After unpacking you have to click the pa

Display parts, controls and connectors44Dual-head standFigure 16: Dual-head stand (rear view)3. Arm covers.The covers are packaged separately from the

Single-head installation45Single-head installationTo attach the panel unit to the display stand:1. Take the display stand from the packaging and put i

Single-head installation46To detach the panel unit from the display stand:1. Firmly push the push-button at the rear of the panel (3) or (4). Push but

Dual-head installation47Dual-head installationTo attach the panel units to the dual-head stand:1. Take the stand from the packaging and put it on a so

Dual-head installation48Figure 19: Example of label with position for bracketsFigure 20: Shift brackets according to label indication4. Take one of th

Dual-head installation495. Hook the top gaps in the rear of the panel over the top anchors of the bracket (figure 21 below).6. Push the bottom of the

Table of Contents5Table of ContentsPreface... 7Regulatory compliance

Vesa-mount installation50Vesa-mount installationImportant:• Use an arm that is approved by VESA (according to the VESA 100 mm standard).• Use an arm t

Adjust panel orientation51Adjust panel orientationTo adjust the panel orientation:1. Before turning the display panel, lift it in its heighest positio

Connecting the signal cables52Connecting the signal cablesTo connect the signal cables to the display:1. Make sure the computer is turned off.2. To ge

Connecting the signal cables535. Connect signal cables:Figure 26: Signal cable connections• Connect one end of the DVI cable to the DVI input of the d

Connecting the signal cables54Figure 27: External DC power supply78

Cable routing55Cable routingTo route the cables:Figure 28: Display rear view1. Bind the cables in the connector compartment together with the cable ti

Cable routing563. Unpack the plastic stand arm covers and attach them to the display stand.To attach the arm covers, first slide the covers horizontal

Cable routing574. Close the cable duct covers. Push the cable duct covers upward to lock them.Figure 30: Installation complete

Cleaning instructions58Cleaning instructionsPrecautions• Take care not to damage or scratch the glass or LCD panel. Be careful with rings or other jew

Cleaning instructions59• Detergents with ammonia• Detergents with abrasives• Steel wool• Sponge with abrasives• Steel blades• Cloth with steel threadC

Table of Contents6Connecting the signal cables... 52Cable routing...

Cleaning instructions(This page intentionally left blank.)60

Software installation61Software installation

Driver and Software Installation62Driver and Software InstallationThis chapter will guide you through the installation of the drivers, software and do

Driver and Software Installation63• Windows XP Professional x64 Edition, • Windows Server 2003,• Windows Server 2003 x64 Edition, • Windows Server 200

Driver and Software Installation64b) Click Run. c) Click Browse and browse to the root directory of the BARCO CORONIS Display System Installation CD-R

Driver and Software Installation6510. When the Setup complete message appears, select Reboot System Now and click Finish.11. After the system reboots,

Driver and Software Installation66Figure 31: Barco MXRT Driver Removal Wizard (driver version may be different than what is pictured)Note: Vista Only:

Driver and Software Installation67To install the drivers and software silently, please follow the steps below:1. Insert the BARCO CORONIS Display Syst

Driver and Software Installation68Figure 32: Command line installationNote: When performing an MXRT driver upgrade, it is essential to uninstall the p

Driver and Software Installation69• Windows Server 2003 x64 Edition, and• Windows Vista 32 & 64 Bit Edition.You will need to install the BARCO COR

Preface7Preface

Driver and Software Installation704. Follow the wizard’s on-screen instructions to complete the installation.Note: When the page shown in figure 33 ap

Driver and Software Installation71installing for this hardware has not passed Windows logo testing.Automated display configurationOnce the drivers, so

Driver and Software Installation72Figure 34: Barco Driver Removal WizardCommand line (Silent) Install of Drivers and Software(Not supported with Windo

Driver and Software Installation73a) Browse to the root directory of the BARCO CORONIS Display System Installation CD-ROM.b) Click on the file, Setup.

Driver and Software Installation(This page intentionally left blank.)74

Where to get more information75Where to get more informationWhere to find more informationThe following documentation is included with your system:Abo

Where to get more information76•In the Security section, check the option Allow active content to run in files on My Computer

Troubleshooting77Troubleshooting

General tips78General tips• If one display from a multi-head system exhibits problems, try to eliminate the problem by switching video cables or power

Configuring Windows79Configuring WindowsSetting the resolution of your BARCO CORONIS DisplayNote: In order to set the resolution of your BARCO CORONIS

Regulatory compliance information8Regulatory compliance informationFCC Compliance Information CLASS B:This device complies with part 15 of the FCC rul

Configuring Windows80rectangle for the virtual display representing the two heads controlled by each BarcoMed display controller output.If you install

Configuring Windows81To set the resolution of the second display attached to the BarcoMed display controller you are working with, go back to the “Set

Configuring Windows(This page intentionally left blank.)82

Technical Specifications83Technical Specifications

Technical Specifications84:Item MDCG 2121 MDCG 3120Product acronym MDCG 2121 MDCG 3120Screen technology TFT AM LCD Dual Domain IPS TFT AM LCD Dual Dom

Technical Specifications85Maximum lumi-nance*1650 cd/m² 1000 cd/m² DICOM calibrated luminance (ULT off)*500 cd/m² 500 cd/m² Contrast ratio (typi-cal)*

Technical Specifications86Dimensions with stand (W x H x D)Portrait: 369 x 558~658 x 285 mm Landscape: 477 x 504~604 x 285 mm Portrait: 369 x 558~658

Technical Specifications87Certifications IEC 60950-1:2005, IEC 60601-1:1988 + A1:1991 + A2:1995, IEC 60601-1:2005, IEC 60601-1-2:2007, UL 60950-1, 1st

Technical Specifications88Supplied accessories Getting Started Guide Quick-Installation Sheet Video cable (DVI Dual Link) Main cables (UK, European (C

Technical Specifications89Item MDCC 2121Product acronym MDCC 2121Screen technology TFT AM LCD Dual Domain IPS Active screen size (diagonal)541 mm (21.

Regulatory compliance information9Canadian noticeThis ISM device complies with Canadian ICES-001.Cet appareil ISM est conforme à la norme NMB-001 du C

Technical Specifications90Contrast ratio (typi-cal)*1100:1Response time (Tr + Tf)17 msScanning frequency (H; V)30-150 kHz; 15-80 Hz Housing color Gray

Technical Specifications91Net weight w/o stand9.0 kg Net weight pack-aged with stand19.0 kg Net weight pack-aged w/o stand12.0 kg Height adjustment ra

Technical Specifications92Supplied accessories Getting Started Guide Quick-Installation Sheet Video cable (DVI Dual Link) Main cables (UK, European (C

Warranty Statement93Warranty StatementBARCO MID GENERAL WARRANTY TERMS AND CONDITIONSApplicable from Jan 1st 2008 ARTICLE 1: PRODUCT WARRANTYBarco nv,

Warranty Statement94Replacement parts used shall be new or equivalent to new parts for the revision level of the equipment. A replacement LCD panel wi

Warranty Statement952.5Repair or replacement of consumables1 or specific parts that by definition are subject to wear and tear, including but not lim

Warranty Statement96Replacement of moveable parts such as power cords, remote controls, …2.7Any product disassembly and installation costs at the oper

Warranty Statement97remedy and Barco's sole and exclusive liability for Barco’s breach of the Warranties hereunder.BARCO NV, MID SHALL NOT UNDER

Warranty Statement98

Warranty Statement99