Barco R9855938 Installation Manual

Xenon bulb lamp replacementInstallation manualFor DP-1200/DP-1500/DP-2000R59770175/0124/09/2008

1. Xenon bulb lamp6 R59770175 XENON BULB LAMP REPLACEMENT 24/09/2008

2. Xenon bulb lamp replacement process2. XENON BULB LAMP REPLACEMENT PROCESSAbout this cha p terThis chapter describes how to re place the xenon bulb

2. Xenon bulb lamp replacement process2.1 Removal of the lamp houseWARNING: This procedure may only be performed by qualified technical service personn

2. Xenon bulb lamp replacement processWhile starting up the projector, the electronics d etect if a lamp is ins talled. If no lam p is installed, it i

2. Xenon bulb lamp replacement process2.2 Removal of the xenon bulb lampWARNING: DO NOT PERMIT UNAUTHORIZED PERSONNEL TO PERFORM OR ATTEMPT ANY PHASE

2. Xenon bulb lamp replacement process3. Release t he xenon bulb lam p from its socket by removing the hexagon socket head cap screw and plane washer

2. Xenon bulb lamp replacement processLN2SW1W2N1N1N2Image 2-67. Remove the cathode lamp adaptor ( A) from the xenon bulb lamp (L) as illustrated. Usea

2. Xenon bulb lamp replacement process2.3 Installation of the xenon bulb lampWARNING: DO NOT PERMIT UNAUTHORIZED PERSONNEL TO PERFORM OR ATTEMPT ANY P

2. Xenon bulb lamp replacement processImage 2-83. Install the lamp cathode adaptor (A ) up on the xenon bulb lamp (L) as illustrated. Usetorque 2,5 N

2. Xenon bulb lamp replacement processLN2SW1W2N1N1N2 9 NmImage 2-105. Remove the protective container or unwr ap the protective cloth from the xenon b

Barco NV Media and Entertainment Division11101 Trade Center Drive, Rancho Cordova, California 95670, USAPhone: +1 916 859-2500Fax: +1 916 859-2515E-ma

2. Xenon bulb lamp replacement processImage 2-128. Reinstall the UV bloc ker asse mbly as illustrated. Make sure that the xenon bulb lamp is properly

2. Xenon bulb lamp replacement process 2,5 NmAImage 2-1511.Reinstall the side cover of the lamp house as illustrated.Note: Please ensure that the thum

2. Xenon bulb lamp replacement process2.4 Installation of t he lamp houseWARNING: This procedure may only be performed by qualified technical service p

2. Xenon bulb lamp replacement processWhile starting up the projector, the electronics d etect if a lamp is ins talled. If no lam p is installed, it i

2. Xenon bulb lamp replacement process2.5 Resetting the lamp parametersCAUTION: The “LA MP INFO” param eters which are stored on a ch ip MUST be updat

2. Xenon bulb lamp replacement process2.6 Realignment of the lamp in its reflectorEach xen on bulb lamp installation requires a realignment of the lamp

2. Xenon bulb lamp replacement processXLYZYLXImage 2-217. Fasten the X-axis lock thu mb screw (ref LX image 2-21) and Y-axis lock thumb screw (refLY i

IndexINDEXIInstall 13, 18Lamp house 18Xenon lamp 13Introduction 4LLamp 20–21Realignment 21Reset 20Lamp house 8, 18Install 18Remove 8RRealignment 21Lam

ChangesBarco p rovides this manua l ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-ra

Table of contentsTABLE OF CON TENTS1. Xenon bulb lamp ...

Table of contents2 R59770175 XENON BULB LAMP REPLACEMENT 24/09/2008

1. Xenon bulb lamp1. XENON BULB LAMPSafetyRead all w arnings and cautions attentively. This to prevent p ersonal injury while installing an xenon bulb

1. Xenon bulb lamp1.1 IntroductionLamp & lamp houseThe xenon bulb lamp is delivered separately and has to b e installed on site by a qualified serv

1. Xenon bulb lamp1.2 Supported xenon bulb lampsSupported xenon bulb lamps (without lamp house)LampTypeOrder infoOsram xenon bulb lamp of 4 kW4kW DHP