Barco MSWU-81E User Manual Page 42
- Page / 85
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
MSWU-81E 29/09/2014
34
5. Getting Started
5.10 Introduction the OSD Lite on screen
Press on RCU or press "Home"
on projector rear cover, You can see
the OSD Lite on screen as above
picture.
INPUT
Use this function to select the input souce. You can choice
HDMI1, HDMI2, VGA, YUV1 and RGBHV/YUV2. Refer to page
37: 7. INPUT for futher message.
BRIGHTNESS
Adjust the level of black in the image to increas or decrease
image brightness. Refer to page 41: 8.3 Brightness
CONTRAST
Adjust the level of white in the image to increase or decrease
image contrast. Refer to page 41: 8.2 Contrast.
COLOR
Adjust the image’s color saturation. When oversaturated, the
colors in the image will appear to be very bright and vivid;
on the other hand, if colors are undersaturated, the image
will appear to be washed out.
ASPECT RATIO
You can select differnt aspect vis this function. Refer to page
45: 8.8 Aspect Ratio .
LENS FOCUS
Use this fuction to adjust the image from fuzzy to clear.
LENS ZOOM
Use this function to zoom in or zoom out the image's size.
KEYSTONE
Use this function to adjust the from the tilt to not inclined.
Refer to page 56: 11.6 Keystone
LANGUAGE
Use this function to select the different language of the OSD
Lite on screen. Refer to page 61: 12.9 Language.
INFO
Show the information of lamp.
MODE
Select ECO, Normal and Power mode of lamp. Refer to page
52: 10.2 Mode.
SERVICE
Display this projector's information. Refer to page 63: 13.2
Service message of the projector
Advance
This function is for futher adjust the projector. For
professional use. Refer to page 35: 6. ADVANCED OSD
MENU
- MSWU-81E 1
- Barco nv Projection Division 2
- 1. SAFETY 1 4
- 2. GENERAL 5 4
- 3. PHYSICAL INSTALLATION 12 4
- 5. GETTING STARTED 29 5
- 6. ADVANCED OSD MENU 35 5
- 7. INPUT 37 5
- 8. IMAGE 40 6
- 9. LAYOUT 48 6
- 10. LAMP 51 6
- 11. ALIGNMENT 54 7
- 12. CONTROL 58 7
- 13. SERVICE 62 7
- 14. MAINTENANCE 64 8
- 1. SAFETY 9
- Users definition 10
- To prevent personal injury 10
- To prevent fire hazard 11
- To prevent projector damage 11
- On servicing 12
- To prevent battery explosion 12
- 2. GENERAL 13
- 2.2 Unpacking the projector 14
- 2.3 Initial inspection 15
- 2.4 Projector configurations 16
- Rear projection 17
- Positioning the projector 17
- On axis / off axis projection 18
- Shift range 18
- Ventilation inlet 19
- Ventilation outlet 19
- 3. PHYSICAL INSTALLATION 20
- Remote Control overview 21
- IR LED'S 21
- 3.2 Lenses 22
- How to remove the lens 23
- Lens focus 24
- Lens zoom 24
- Lens Shift 24
- 3.Physical Installation 25
- This power cord for Europe 26
- Angle adjustment 27
- Necessary tools 28
- How to mount 28
- 4.1 Projector front view 29
- 4.2 Projector Rear view 29
- 4.3 Input and Communication 30
- 3. 12V TRIGGER 31
- 4. IR EXT 31
- 4.4 Status lights of LED 32
- Retractable screen or other 33
- 12V device 33
- Desk Top 34
- RGBs connection 35
- IR INPUT connection 35
- (YPbPr) 36
- 5. GETTING STARTED 37
- 5. Getting Started 38
- 5.3 Power on projector 39
- 5.4 Switching to standby 39
- 5.5 Power off projector 39
- 5.7 Source selection 40
- 5.8 Changing OSD language 41
- 6. ADVANCED OSD MENU 43
- 6.3 Advanced menu memory 44
- 7. INPUT 45
- 7.2 Input Selection 46
- 7.3 Input Configuration 46
- 7.4 Input Locking 46
- 7.5 Auto Power Off 47
- 7.6 Auto Power ON 47
- 7.7 No Signal 47
- 7.8 Auto Image Adjust 47
- 8. IMAGE 48
- 8.2 Contrast 49
- 8.3 Brightness 49
- 8.4 Sharpness 50
- 8.5 Noise Reduction 50
- 8.6 Color Temperature 50
- 8.7 Input Balance 51
- Adjusting the input balance 52
- 8.8 Aspect Ratio 53
- 8.9 Timings 54
- 8.10 Auto Image 55
- 9. LAYOUT 56
- 9.2 Zoom 57
- 9.3 Main Select 57
- 9.4 PIP Select 58
- 9.5 PIP Position 58
- 9.5 PIP 58
- 10. LAMP 59
- 10.2 Mode 60
- 10.3 Lamps 60
- Lamp1 Status 61
- Lamp2 Status 61
- 11. ALIGNMENT 62
- 11.3 Rear Projection 63
- 11.4 Ceiling Mode 64
- 11.5 Lens Control 64
- 11.6 Keystone 64
- 11.7 Dynamic Contrast 64
- 11.9 Color Space 65
- 11.10 Lens To Midposition 65
- 11.8 Gamma 65
- 11.8 Internal Patterns 65
- 12. CONTROL 66
- 12.2 Eco Network Power 67
- 12.3 Network 67
- 12.4 Menu Position 68
- 12.5 Start Up Logo 69
- 12.6 Start Up Chime 69
- 12.7 Trigger1 ~2 69
- 12.8 Auto Source 69
- 12.9 Language 69
- 13. SERVICE 70
- 13.3 Lamp Hour Reset 71
- 13.4 Blue Only 71
- 13.4 Factory Reset 71
- 14. MAINTENANCE 72
- Necessary parts 74
- How to change the filter 74
- Black side 75
- White side 75
- 14.4 Cleaning the lens 76
- 14.6 Simple troubleshooting 77
- 15. PROJECTOR SPECIFICATION 79
- 15.2 STANDARD SOURCE FILES 80
- 15.3 Dimension 81
- 16. ENVIRONMENTAL INFORMATION 82
- 本产品中包含的有毒有害物质/成分的名称和含量。 83
- 16.Environmental information 84
Related products and manuals for Data projectors Barco MSWU-81E
Data projectors Barco RLM-W12 User's Guide
(63 pages)
(63 pages)
(46 pages)
Data projectors Barco FLM R22+ User's Guide
(243 pages)
(243 pages)
Data projectors Barco Galaxy NW-7 User's Guide
(183 pages)
(183 pages)
Data projectors Barco SLM G10 Owner's Manual
(159 pages)
(159 pages)
Data projectors Barco F50 User Manual
(66 pages)
(66 pages)
Data projectors Barco CR series User Manual
(54 pages)
(54 pages)
(87 pages)
Data projectors Barco RLM W6 User's Guide
(57 pages)
(57 pages)
© 2020, manymanuals.com. All rights reserved. | 2.477 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals